dsPIC30F4011
- Modified Harvard architecture
- C compiler optimized instruction set architecture
- 84 base instructions with flexible addressing modes
- 24-bit wide instructions, 16-bit wide data path
- 16 x 16-bit working register array
- Up to 30 MIPs operation:
- DC to 40 MHz external clock input
- 4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)
- Peripheral and External interrupt sources
- 8 user selectable priority levels for each interrupt
- 4 processor exceptions and software traps
- Primary and Alternate interrupt Vector Tables
- Modulo and Bit-Reversed Addressing modes
- Two, 40-bit wide accumulators with optional saturation logic
- 17-bit x 17-bit single cycle hardware fractional/ integer multiplier
- Single cycle Multiply-Accumulate (MAC) operation
- 40-stage Barrel Shifter
- Dual data fetch
- High current sink/source I/O pins: 25 mA/25 mA
- Optionally pair up 16-bit timers into 32-bit timer modules
- 3-wire SPI™ modules (supports 4 Frame modes)
- I2C™ module supports Multi-Master/Slave mode and 7-bit/10-bit addressing
- Addressable UART modules with FIFO buffers
- Complementary or Independent Output modes
- Edge and Center Aligned modes
- Multiple duty cycle generators
- Dedicated time base with 4 modes
- Programmable output polarity
- Dead time control for Complementary mode
- Manual output control
- Trigger for synchronized A/D conversions
- Phase A, Phase B and Index Pulse input
- 16-bit up/down position counter
- Count direction status
- Position Measurement (x2 and x4) mode
- Programmable digital noise filters on inputs
- Alternate 16-bit Timer/Counter mode
- Interrupt on position counter rollover/underflow
- 10-bit 1 Msps Analog-to-Digital Converter (A/D)
- A/D Conversion available during Sleep and Idle
- Sample/Hold Channels
- Multiple Conversion Sequencing Options
- Enhanced Flash program memory:
- 10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)
- Data EEPROM memory:
- 100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)
- Self-reprogrammable under software control
- Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliable operation vv
- Fail-Safe clock monitor operation
- Detects clock failure and switches to on-chip low power RC oscillator
- Programmable code protection
- In-Circuit Serial Programming™ (ICSP™)
- Programmable Brown-out Detection and Reset generation
- Selectable Power Management modes
- Sleep, Idle and Alternate Clock modes
- Low power, high speed Flash technology
- Wide operating voltage range (2.5V to 5.5V)
- Industrial and Extended temperature ranges
- Low power consumption
Parameter NameValueArchitecture16-bitCPU Speed (MIPS)30Memory TypeFlashProgram Memory (KB)48RAM Bytes2,048Temperature Range C-40 to 125Operating Voltage Range (V)2.5 to 5.5I/O Pins30Pin Count40System Management FeaturesBORPORYesWDTYesInternal Oscillator7.37 MHz, 512 kHznanoWatt FeaturesFast Wake/Fast ControlDigital Communication Peripherals2-UART
1-SPI
1-I2C
Analog Peripherals1-A/D 9x10-bit @ 1000(ksps)USB (ch, speed, compliance)0, None,CAN (#, type)1 CANCapture/Compare/PWM Peripherals4/4PWM Resolution bits16Motor Control PWM Channels6Quadrature Encoder Interface (QEI)1Timers5 x 16-bit 2 x 32-bitParallel PortGPIO
Parameter Name
Value
Architecture
16-bit
CPU Speed (MIPS)
30
Memory Type
Flash
Program Memory (KB)
48
RAM Bytes
2,048
Temperature Range C
-40 to 125
Operating Voltage Range (V)
2.5 to 5.5
I/O Pins
30
Pin Count
40
System Management Features
BOR
POR
Yes
WDT
Yes
Internal Oscillator
7.37 MHz, 512 kHz
nanoWatt Features
Fast Wake/Fast Control
Digital Communication Peripherals
2-UART
1-SPI
1-I2C
1-SPI
1-I2C
Analog Peripherals
1-A/D 9x10-bit @ 1000(ksps)
USB (ch, speed, compliance)
0, None,
CAN (#, type)
1 CAN
Capture/Compare/PWM Peripherals
4/4
PWM Resolution bits
16
Motor Control PWM Channels
6
Quadrature Encoder Interface (QEI)
1
Timers
5 x 16-bit 2 x 32-bit
Parallel Port
GPIO